Repiping Of A House


Homeowners will always confront problems with plumbing. It is unavoidable. But sometimes it’s not enough to have a simple repair—you have to repipe a house. A full house repipe seems like an enormous project, but you must not be bullied. In this tutorial, we will go through the whole process, from evaluating if a pipe is needed to select a plumber and what pipe materials to look at.

A slight disclaimer: Repiping is not a job for you if you have the true, professional plumbing experience. The home is repiped with demolishment, plumbing, rebuilding, and in certain cases with an open flame. Don’t try to do yourself any of this.

When You Need Repiping Of A House?

Repipe a house is a major undertaking. It’s a major time and money investment. However, it is often advised or even essential to have your aging pipes updated. Here are some causes for your house repipe:

  • You pay for plumbing and repairs frequently. The remaining plumbing problems might get rid of a new pipe network. With a fresh new system, you may prevent future repairs on the road for many years.
  • The steel pipes in your house are galvanized. Galvanized steel was a mainstay in pipes before World War II in American houses. The difficulty with galvanized pipes is that they can get rusted after a certain number of years. As soon as the corrosion in these pipes begins, the flow of water is reduced and the sediment in your drinking water may end.
  • You want to undertake a restructuring. If you want to build new bathrooms or other plumbing devices, you may save both time and money by replacing them at the same time.

Preparation For Repipe a house

The job is quite simple to prepare to repipe a house. Your plumber should carry out a thorough assessment of your home’s plumbing system, assessing the pipe length and cost. You should talk to me about your new pipe alternatives. Then they should give you a full estimate of the type of pipe they will put into your home and the entire cost to you.

Your plumber might also inquire whether the last time you have painted walls or a record of colors you used, you have remaining paint. The plumber’s musculus into many places in your home throughout the repiping operation. The wall and the finish should be replaced.

Installation Process

While installing the plumbers, they will go into the home and lay down floor planes or other objects that may be harmed if the plumbing leaks minorly during the pipe change.

Depending on the size of the house, installation may take a few days and the duration may usually be limited to a few hours every day by a plumber. The water is shut. That being stated, the pipes are occasionally so broken or uncertain that the entire water installation procedure must be switched off.

In advance, the plumber should inform you how long the water needs to stay away.

Just before the installation is finished, your plumbers will test the pipes before they leave. They should also make sure that the walls are complete, notify you when you are trying, and clean them up if anything is still done.

How to Remove a Shower Drain

How to Remove a Shower Drain

In our homes there are some shower drains fixed in bathrooms, kitchens, and balconies. A shower drain is composed of four basic parts:

  • Grid
  • Strainer
  • Vent
  • Trap

The primary function of the shower drain is to drain the wastewater into the sewerage system and to maintain the interior air quality of bathrooms. But sometimes it stops draining wastewater which creates a big hurdle for us. So in this regard, we must know How to remove the shower drain? So that we become able to repair or replace it easily. Before removing the shower drain you must have some basic tools e.g.

  • Utility knife
  • Screwdriver
  • Pliers

Here are the 12 easy steps which help you to get an answer on how to remove the shower drain.

1: Buy some lubricants

The first step is to purchase some lubricants. These lubricants are used to close the shower drain so that we can remove it easily. WD-40 is a highly recommended lubricant.

2: Drying of shower drain

Before applying the lubricant you must dry the shower drain properly with any cloth piece or with a towel. Drying is important because with a wet shower drain the lubricant may not work properly.

3: Clog checking

Check the drain properly and find out if there is any clog or not. In case If you find any clog there then you have to unclog it first and then apply the lubricant.

4: Apply the lubricant

After checking the clog and letting it dry, now apply any sort of lubricant gently on the shower drain as well as put some lubricant inside it.

5: Find the type of shower drain

Mostly, there are two types of shower drains. One is the screw-fixed shower drain and another one is the flat one which is tightened on the floor without any screw. So If it the screw-fixed type then use a screwdriver to unscrew it.

6: Put the pliers

Now, you have to put the head of two separate pliers in two small holes of the shower drain.

7: Clasp the handles of pliers

Most of the shower drains are fixed into the floor just like the screws are fitted. So in this regard, clasp the handles of pliers and untwist them. This step is just like removing a screw with the help of a screwdriver.

8: Untwisting

After grabbing the handles of pliers, start untwisting the shower drain until it is completely separated from the floor.

9: Uplift the Shower drainer

Now uplift the shower drainer with the help of pliers gently to avoid any sort of damage. If you are still feeling difficult to lift it then use a little lubricant again.

10: Use the pliers carefully

While lifting the shower drainer, handle the pliers carefully. Neither you should grab the handles of pliers tightly nor you should grab them too loosely.

11: Examine the shower drain

As you have removed it successfully, now check the shower drainer carefully if there is any rust, clog, dirt or something has stuck in it. Remove these things and try to fix them before rejecting the shower drain.

12: Replace the shower drain

If you find there any severe damage which is not fixable then call a plumber and replace it with a new one.

Here is a guide that helps you how to remove the shower drain. Feel free to contact us.

Best gas water heater repair services

Best gas water heater repair services

A gas heater heats cold water and stores the hot water in the tank installed inside it. This hot water is later used for various purposes when needed at home, restaurants, hotels, shops, or anywhere else where it is required.

Often people take water heaters for granted. People usually don’t pay much attention to the water heater until it stops making hot water. Although that doesn’t happen very often, we still need to check the heater regularly and use it in a usual way. This article provides information on repairing the water heater if it becomes malfunctioned or needs to be replaced.

This information includes types of water heater, gas water heater repair options, and how you can troubleshoot minor problems independently without needing to call a plumber.

Types of water heater

There are several types of water heater available in the market.

1- Tankless water heater

Tankless water heaters are energy efficient. They heat water instantaneously and on-demand. Some disadvantages include that a tankless water heater provides a low flow rate; usually, three-five gallons a minute, and only one user can use it at a time.

2- Electric heat pump water heater

Electric water heaters use electricity as a source of power. They draw air from the surroundings and heat this air to heat the water stored in them. Electric heaters are usually suitable for use in a warmer climate.

3- Solar water heaters

Solar water heaters are powered by the sun, unlike others which require electricity natural gas to work. They are made up of two components, mainly a solar panel and an insulated storage tank. Solar panel heats the water, and heated water is stored in the tank. Solar water heaters work in any environment and have an average lifespan of 15-20 years.

Gas water heater repair?

Many homeowners prefer to repair a malfunctioning or faulty heater instead of installing a new model. The best time to replace a water heater is at the end of its lifespan. A typical water heater has a lifespan of 10-15 years, whereas a Solar water heater has up to 20 years of lifespan.

But, in case your water heater is just a few years old and is causing problems, there are few ways to diagnose the issue in the heater. Common issues include

  • The pilot light is not turning on or going out when the heater is turned on.
  • The circuit breaker of the electric pump tripping continuously.
  • Heaters and burning elements are not working correctly.
  • Thermostats are breaking, and valves are not functioning properly.

Reduce the repair needs of your water heater

If you want to avoid gas water heater repairs and issues in your heater, you need to maintain it properly. That includes checking it every year before the winter season kicks off. Check properly to see if every component is working properly. Clean the tank to remove any sediments. Replace the sacrificial rod every three years; these rods made up of aluminum or Magnesium become eroded.

You can enlist the help of professional plumbers to help in maintaining the water heater. If you can’t diagnose the problem independently, it is wise to call a plumber before the problem worsens. A plumber can help pinpoint the source of problem and also repair it at a very reasonable price. The plumber can also recommend new heaters according to your house needs in case your current heater can’t be repaired.

Grease Trap Pumping And Cleaning

Grease Trap Pumping And Cleaning

A grease trap is a plumbing device designed to catch grease and solids before entering the wastewater system. Typical wastewater contains small amounts of oil, which can block the drain pipes that later can cause an increase in untreated sewage in the environment.

Grease traps help to reduce oil, fats, and greases that enter the sewage system. Make sure to clean them on time to avoid any annoyance. They help to keep your surroundings clean, environment friendly, and without any unpleasant smell.

Where are Grease traps located?

Grease traps are mainly found outside restaurant buildings. Since restaurants produce extra oil and other greasy waste from cleaning dishes that have leftover food on them, look near a restaurant’s dishwashing station. You will see it. They look like a standard manhole with a lid covering them.

What is grease trap pumping?

As mentioned, grease traps intercept the grease and oil coming from kitchen waste before the waste enters the primary sewage system. This happens because grease and oil are light in weight in comparison to water and other waste substances. These lightweight particles float on top of the waste coming from kitchens. Grease traps intercept this waste and allow grease-free waste to enter the main sewage line. After these lightweight solid particles are caught in grease traps, they need to be removed, so they don’t contaminate and block the sewage line. This process of cleaning is called grease trap pumping, where the waste contained in these traps is removed.

How to clean grease traps?

Grease trap pumping and cleaning is a way of removing the grease from these traps. There are numerous ways by which you can clean grease traps. You can do it yourself or ask a professional plumbing company that offers grease trap pumping and cleaning services to do it for you regularly. We will discuss here how you can do it yourself.

First, you have to wait before your restaurant closes and all the dishes and other food-contained items are cleaned. You can clean it early in the morning as well. It doesn’t matter when you decide to clean; follow the steps below.

  1. Remove the lid of the traps slowly and gently. Make sure to not damage the gaskets on the lid.
  2. Stick a ruler in the grease trap to check how much inch’s waste has been collected. Record this in a log sheet.
  3. Remove water from the trap using a pump.
  4. Now start removing grease from the trap using a bucket, shovel, or any other device which suits you the most.
  5. Ensure to check the bottom, sides, and lid of the trap to see if any grease is there. This will prevent quick build-ups and prevent solidifying of waste, which becomes difficult to remove.
  6. Scrub the trap to make sure last time that all the waste has been removed.
  7. Place the lid back again on the grease trap.

Follow these steps if you plan on doing a cleaning of grease traps yourself.

replacing copper pipes with pex

Replacing Copper Pipes With PEX: An Easy Plumbing Upgrade

For many years copper has had a name in the plumbing field due to its amazing specifications of heat resistance and high-pressure resistance but the problem with the use of copper is:  It is more expensive than other materials. The other material that we are taking the space of copper is PEX. It is a step towards advancement and progress in the field of plumbing.

PEX is a cross-link polyethene end pipe with crosslinks. The polyethylene used in these pipes is of high density having crosslinks bonds. There are two types of polyethene: the first is cross-linked polyethylene and the second one is non crosslinked polyethylene. Cross-linked polyethene has specifications of thermal and mechanical properties. So replacing copper pipes with pex is best.

Hard Water Creates Problem in Copper Pipes

Hard water contains calcium and magnesium and it has an acidic effect on copper pipes and causes a leak. The solution to this problem is replacing copper pipes with pex but the question arises how to replace copper pipes with pex, here is a complete procedure that helps you to replace copper pipes with pex. For replacement, you don’t need to call a plumber and spend extra money on a task that you can easily do yourself. Here are a few directions that can guide you on how to replace the copper pipe with pex. Just follow it and make the plumber of your own house.


The basic tools you required for replacing copper pipes with pex are following

  • Few fittings
  • Pipe cutter
  • PEX crimping tools
  • Measuring Tape
  • Marker
  • Drill Driver


The important materials required are

  • Copper pipe straps
  • PEX tubing
  • Push-fit straight joining
  • Push-fit


Here is the Procedure:

1- Turn off water supply

Before replacing copper pipes with pex, turn off the water supply and remove water from the pipes. Open the valve that is at the basement or first floor of your home to drain the pipes. It will help avoid any disturbance during replacement and you can do your work without any disruptions.

2- Cut the corroded area of copper pipe

Mark the pipe that contains a corroded area in it. Use a tubing cutter and cut both ends of the pipe.

3- Fit the PEX to copper tube

Cut the PEX tube that is long enough as compared to the cutting area with the help of the PEX tubing cutter. Clean the ends of the PEX tube and fit it with the help of a push-fit connector. You can also use a push-fit valve instead of a straight connector. It’s your choice.

4- The electrical system should be grounded

When you are replacing copper pipes there is no need for the ground but if you are replacing metal pipes then you must keep in your mind to check whether the electrical system is grounded, if not then firstly do it.

Here is a complete guide to replacing copper pipes with pex. For further details feel free to contact us. We will be glad to help you.

clogged kitchen sink

Clogged Kitchen Sink | How to Unclog Your Kitchen Sink Drain

The kitchen is every woman’s part of life. And to wash dishes and other utensils is one of the tasks that we all are doing. If you are washing dishes and suddenly you notice the water is not draining then what will happen. You faced the situation of a clogged kitchen sink! And this is not the situation you are just facing, many of us face this situation, but what is the solution? Calling a plumber is a solution. It is but avoids doing this gives you a jerk of extra cost. Some of your time only fixes it. Here are 5 steps to a fresh drain. You can use any of it, the choice is yours. The method also depends on the nature of your clog.

Remove standing water:

Before doing steps to unclogging first deal with standing water. Try to remove all standing water with the help of a container. Then you can easily eliminate the waste. If there is waste at the garbage disposal then don’t put your hands near it. Sometimes you can remove the waste from your hand and sometimes it takes further actions.

Use boiling water:

Heat the water in a separate utensil. After removing the standing water, pour that boiled water into it and wait for five to six minutes. If the boiled water becomes standing water then clog remains. Cooldown the water and then remove it with the help of a jug.

Try another method

Garbage disposal:

Improper functioning of a garbage disposal can also be the cause of a clogged kitchen sink. Inspect garbage disposal; is it working properly? Is it heated? If it is heated then turn it off and do start after some time. Also do check whether anything hasn’t stuck in it. Use tongs or pliers to remove any material that has been stuck between the blades. A garbage disposal can also be switched off due to heat in this case you need to restart it.

Use baking soda and vinegar:

Before the implementation of this method try to remove any standing water from it. Pour a cup of vinegar and baking soda into the sink. Wait for 15 minutes, add hot water and see if the clog clears or is going to clear. Repeat this process so that water starts draining normally.

Clean the pipe:

Try to clean the P trap that is the pipe under the sink. How to clean it? Here are steps that help you to clean the P trap

  • Put a bucket for water that is in your sink
  • Remove the pipe and then try to remove waste from it.

There are many other methods to clear the clogged kitchen sink using a plunger, plumber’s snake and using a hanger. It’s up to you which method you want to use and which one is more effective to clear the clog. If you have any questions feel free to contact us. We will feel pleasure to help you.